#521  (Permalink
Alt 25.01.2019, 12:26
DanijelT DanijelT ist offline
Neues Mitglied
 
Registriert seit: 24.01.2019
Beiträge: 4
Standard AW: Speedport W724V

Bootlog with P2812 U-Boot flashed to NAND and W921 image loaded via TFTP:

Code:
ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  256 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0 
P-2812HNU-Fx # tftpboot 0x81000000 192.168.1.87:initramfs-vgv953.bin
ltq_phy: addr 0, link 1, speed 100, duplex 1
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 100, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.87; our IP address is 192.168.1.1
Filename 'initramfs-vgv953.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ########################################
         2.5 MiB/s
done
Bytes transferred = 4391866 (4303ba hex)
P-2812HNU-Fx # bootm
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.18
   Created:      2015-07-31  11:36:05 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4391802 Bytes = 4.2 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.18 (cornelus@dell) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #60 Fri Jul 31 14:35:09 EEST 2015
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV953 - SPEEDPORT W921V
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00051020
[    0.000000] Readback ErrCtl register=00051020
[    0.000000] Memory: 122288K/131072K available (3319K kernel code, 148K rwdata, 932K rodata, 2940K init, 205K bss, 8784K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.164000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.168000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.172000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.176000]   IO 0x000000001ae00000..0x000000001affffff
[    0.200000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.204000] usbcore: registered new interface driver usbfs
[    0.208000] usbcore: registered new interface driver hub
[    0.212000] usbcore: registered new device driver usb
[    0.216000] PCI host bridge to bus 0000:00
[    0.220000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.224000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.232000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x18003fff]
[    0.236000] Switched to clocksource MIPS
[    0.240000] NET: Registered protocol family 2
[    0.244000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.252000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.260000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.264000] TCP: reno registered
[    0.268000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.272000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.280000] NET: Registered protocol family 1
[    4.660000] gptu: totally 6 16-bit timers/counters
[    4.664000] gptu: misc_register on minor 63
[    4.668000] gptu: succeeded to request irq 126
[    4.672000] gptu: succeeded to request irq 127
[    4.676000] gptu: succeeded to request irq 128
[    4.680000] gptu: succeeded to request irq 129
[    4.684000] gptu: succeeded to request irq 130
[    4.692000] gptu: succeeded to request irq 131
[    4.696000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    4.704000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7980000
[    4.708000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7980000
[    4.816000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    4.824000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    4.828000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    4.840000] msgmni has been set to 238
[    4.844000] io scheduler noop registered
[    4.848000] io scheduler deadline registered (default)
[    4.852000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    4.864000] console [ttyLTQ0] enabled
[    4.864000] console [ttyLTQ0] enabled
[    4.872000] bootconsole [early0] disabled
[    4.872000] bootconsole [early0] disabled
[    4.880000] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    4.880000] nand: Macronix MX30LF1GE8AB
[    4.880000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    4.896000] Scanning device for bad blocks
[    4.992000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    4.996000] Creating 4 MTD partitions on "10000000.nand-parts":
[    5.004000] 0x000000000000-0x000000040000 : "uboot"
[    5.008000] 0x000000040000-0x000000060000 : "uboot-env"
[    5.012000] 0x000000060000-0x000000260000 : "kernel"
[    5.020000] 0x000000260000-0x000002000000 : "ubi"
[    5.128000] libphy: lantiq,xrx200-mdio: probed
[    5.144000] net-xrx200: invalid MAC, using random
[    5.148000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    5.156000] eth0: attached PHY [Generic PHY] (phy_addr=0:01, irq=-1)
[    5.224000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    5.292000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    5.300000] wdt 1f8803f0.watchdog: Init done
[    5.304000] TCP: cubic registered
[    5.304000] NET: Registered protocol family 17
[    5.312000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    5.324000] 8021q: 802.1Q VLAN Support v1.8
[    5.328000] UBI: auto-attach mtd3
[    5.332000] UBI: attaching mtd3 to ubi0
[    5.384000] UBI: scanning is finished
[    5.400000] UBI: attached mtd3 (name "ubi", size 29 MiB) to ubi0
[    5.404000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    5.408000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    5.416000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    5.424000] UBI: good PEBs: 237, bad PEBs: 0, corrupted PEBs: 0
[    5.428000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    5.436000] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1043616540
[    5.444000] UBI: available PEBs: 0, total reserved PEBs: 237, PEBs reserved for bad PEB handling: 20
[    5.456000] UBI: background thread "ubi_bgt0d" sta[    5.468000] Freeing unused kernel memory: 2940K (80451000 - 80730000)
[    5.488000] init: Console is alive
[    5.492000] init: - watchdog -
[    5.544000] SCSI subsystem initialized
[    5.556000] dwc2 1e101000.ifxhcd: requested GPIO 488
[    6.148000] eth0: port 0 got link
[    6.416000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    6.416000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    6.424000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    6.432000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.432000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    6.444000] hub 1-0:1.0: USB hub found
[    6.448000] hub 1-0:1.0: 1 port detected
[    7.312000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    7.312000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    7.320000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    7.328000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    7.328000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    7.340000] hub 2-0:1.0: USB hub found
[    7.344000] hub 2-0:1.0: 1 port detected
[    7.352000] usbcore: registered new interface driver usb-storage
[    7.496000] init: - preinit -
[    7.608000] random: procd urandom read with 29 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.736000] procd: - early -
[   10.736000] procd: - watchdog -
Failed to connect to ubus
[   11.316000] procd: - ubus -
[   12.328000] procd: - init -
Please press Enter to activate this console.
[   13.220000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   13.244000] NET: Registered protocol family 10
[   13.260000] NET: Registered protocol family 8
[   13.260000] NET: Registered protocol family 20
[   13.276000] PPP generic driver version 2.4.2
[   13.288000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.312000] MEI CPE Driver, Version 1.2.0

[   13.316000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   13.336000] 
[   13.336000] Predefined debug level: 2
[   13.352000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.360000] Infineon Technologies DEU driver version 2.0.0 
[   13.368000] IFX DEU DES initialized (multiblock).
[   13.372000] IFX DEU AES initialized (multiblock).
[   13.376000] IFX DEU ARC4 initialized (multiblock).
[   13.380000] IFX DEU SHA1 initialized.
[   13.384000] IFX DEU MD5 initialized.
[   13.388000] IFX DEU SHA1_HMAC initialized.
[   13.392000] IFX DEU MD5_HMAC initialized.
[   13.404000] nf_conntrack version 0.5.0 (1956 buckets, 7824 max)
[   13.428000] NET: Registered protocol family 24
[   13.432000] usbcore: registered new interface driver usblp
[   13.440000] usbcore: registered new interface driver usbserial
[   13.444000] usbcore: registered new interface driver usbserial_generic
[   13.452000] usbserial: USB Serial support registered for generic
[   13.476000] xt_time: kernel timezone is -0000
[   13.500000] usbcore: registered new interface driver option
[   13.504000] usbserial: USB Serial support registered for GSM modem (1-port)
ioctl ATM_SETESI: No such device
[   18.412000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   18.416000] ifxmips_ptm: PTM init succeed
[   18.900000] device eth0.1 entered promiscuous mode
[   18.904000] device eth0 entered promiscuous mode
[   18.912000] br-lan: port 1(eth0.1) entered forwarding state
[   18.916000] br-lan: port 1(eth0.1) entered forwarding state
[   20.920000] br-lan: port 1(eth0.1) entered forwarding state
[   31.988000] random: nonblocking pool is initialized



BusyBox v1.23.2 (2015-07-24 22:07:43 EEST) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Chaos Calmer, r46450)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#
Loading any other image causes LZMA error, I guess that's due to wrong RAM configuration so U-Boot overwrites larger images when decompressing.


Zitat:
Zitat von A1B2C3D4 Beitrag anzeigen
The main problem is that the open source b43 driver only supports IEEE 802.11g, making the router unusable for most applications. DECT is not supported either.
For me, it's good enough. But also, according to kernel.org wiki, BCM43222 should have all modes supported (a/b/g/n) since kernel 3.8.
Mit Zitat antworten
  #522  (Permalink
Alt 25.01.2019, 13:44
A1B2C3D4 A1B2C3D4 ist offline
Senior Mitglied
 
Registriert seit: 28.08.2013
Beiträge: 11.050
Provider: T VVDSL, VF DOCSIS 3.0
Standard AW: Speedport W724V

"a/b/g/n" refers to the theoretical capabilities of the Broadcom chipset. The reverse-engineered b43 driver itself only supports IEEE 802.11g.
Mit Zitat antworten
  #523  (Permalink
Alt 26.01.2019, 01:52
DanijelT DanijelT ist offline
Neues Mitglied
 
Registriert seit: 24.01.2019
Beiträge: 4
Standard AW: Speedport W724V

@A1B2C3D4: still, not a big problem for me, I don't make heavy use of wireless. Also, every other BCM43xx OpenWrt device suffers from the same issue.



U-Boot is giving me a lot of trouble and I have to use ugly workarounds, but I managed to boot recent trunk (5bac623895). Wireless not working yet, but VMMC core appears functional.



Code:
[    0.000000] Linux version 4.14.95 (danijel@dev) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9131-5bac623895)) #0 SMP Thu Jan 24 14:53:04 2019
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is Arcadyan VGV9510
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 07e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x4a0 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @8110d000 s25936 r8192 d23216 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32004
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00051028
[    0.000000] Readback ErrCtl register=00051028
[    0.000000] Memory: 119716K/129024K available (4941K kernel code, 189K rwdata, 1340K rodata, 1256K init, 228K bss, 9308K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007907] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.045981] pid_max: default: 32768 minimum: 301
[    0.050899] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.057406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.066775] Hierarchical SRCU implementation.
[    0.072225] smp: Bringing up secondary CPUs ...
[    0.076663] smp: Brought up 1 node, 1 CPU
[    0.085518] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.095188] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.101482] pinctrl core: initialized pinctrl subsystem
[    0.107879] NET: Registered protocol family 16
[    0.119178] pinctrl-xway 1e100b10.pinmux: Init done
[    0.124884] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.134103] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.145054] PCI host bridge /fpi@10000000/pci@e105400 ranges:
[    0.150728]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.155981]   IO 0x000000001ae00000..0x000000001affffff
[    0.203168] usbcore: registered new interface driver usbfs
[    0.208689] usbcore: registered new interface driver hub
[    0.214075] usbcore: registered new device driver usb
[    0.219492] PCI host bridge to bus 0000:00
[    0.223504] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.230415] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.237359] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.244214] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.252704] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x18003fff]
[    0.265725] clocksource: Switched to clocksource MIPS
[    0.272162] NET: Registered protocol family 2
[    0.277447] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.284365] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.290739] TCP: Hash tables configured (established 1024 bind 1024)
[    0.297330] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.303115] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.309724] NET: Registered protocol family 1
[    0.317904] gptu: totally 6 16-bit timers/counters
[    0.322835] gptu: misc_register on minor 63
[    0.326985] gptu: succeeded to request irq 126
[    0.331474] gptu: succeeded to request irq 127
[    0.335987] gptu: succeeded to request irq 128
[    0.340507] gptu: succeeded to request irq 129
[    0.345030] gptu: succeeded to request irq 130
[    0.349531] gptu: succeeded to request irq 131
[    0.357140] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.362468] lantiq,vmmc 1f103000.vmmc: requested GPIO 493
[    0.367927] lantiq,vmmc 1f103000.vmmc: requested GPIO 492
[    0.373370] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x07b00000
[    0.381636] Crashlog allocated RAM at address 0x3f00000
[    0.392075] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.405153] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410898] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.439578] io scheduler noop registered
[    0.443490] io scheduler deadline registered (default)
[    0.451129] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.460139] console [ttyLTQ0] enabled
[    0.460139] console [ttyLTQ0] enabled
[    0.467390] bootconsole [early0] disabled
[    0.467390] bootconsole [early0] disabled
[    0.477324] cacheinfo: Failed to find cpu0 device node
[    0.481084] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.490664] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    0.495691] nand: Macronix MX30LF1GE8AB
[    0.499463] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.507036] Scanning device for bad blocks
[    0.611163] 4 fixed-partitions partitions found on MTD device 14000000.nand
[    0.616735] Creating 4 MTD partitions on "14000000.nand":
[    0.622129] 0x000000000000-0x000000040000 : "uboot"
[    0.628164] 0x000000040000-0x000000060000 : "uboot-env"
[    0.633427] 0x000000060000-0x000000460000 : "kernel"
[    0.638380] 0x000000460000-0x000008000000 : "rootfs"
[    0.644977] mtd: device 3 (rootfs) set to be root filesystem
[    0.652930] 1 squashfs-split partitions found on MTD device rootfs
[    0.657776] 0x000000b20000-0x000008000000 : "rootfs_data"
[    0.667656] libphy: Fixed MDIO Bus: probed
[    0.672764] wdt 1f8803f0.watchdog: Init done
[    0.677641] NET: Registered protocol family 10
[    0.694549] Segment Routing with IPv6
[    0.697025] NET: Registered protocol family 17
[    0.701342] 8021q: 802.1Q VLAN Support v1.8
[    0.814089] libphy: lantiq,xrx200-mdio: probed
[    0.823054] net-xrx200: invalid MAC, using random
[    0.897042] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:00, irq=POLL)
[    0.981019] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:01, irq=POLL)
[    1.065003] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
[    1.149002] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
[    1.164442] random: [    1.172994] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.182578] Freeing unused kernel memory: 1256K
[    1.185724] This architecture does not have kernel memory protection.
[    1.839185] init: Console is alive
[    1.841656] init: - watchdog -
[    3.036727] lantiq,xrx200-net 1e108000.eth eth0: port 0 got link
[    3.184054] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.280718] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[    3.356108] b43-pci-bridge: probe of 0000:00:0e.0 failed with error -2
[    3.370901] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.387417] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.503828] mount_root: no usable overlay filesystem found, using tmpfs overlay
[    7.548830] urandom-seed: Seed file not found (/etc/urandom.seed)
[    7.762639] procd: - early -
[    7.764272] procd: - watchdog -
[    8.356466] lantiq,xrx200-net 1e108000.eth eth0: port 0 lost link
[    8.416588] procd: - watchdog -
[    8.418893] procd: - ubus -
[    8.533305] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.544778] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.550464] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.558180] procd: - init -
Please press Enter to activate this console.
[    9.089574] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.098626] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[    9.112492] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[    9.129759] NET: Registered protocol family 8
[    9.132767] NET: Registered protocol family 20
[    9.145374] PPP generic driver version 2.4.2
[    9.157448] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.185474] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[    9.198596] 
[    9.198596] 
[    9.198596] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[    9.216256] 
[    9.216256] Predefined debug level: 3
[    9.229188] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0
[    9.235330] Backport generated by backports.git v4.19.7-1-0-g148b072d
[    9.253281] Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[    9.260661] request_timer(2, 0x000001AE, 1)...
[    9.260687] successful!
[    9.267828] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[    9.279131] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.289527] Infineon Technologies DEU driver version 2.0.0 
[    9.296285] IFX DEU DES initialized (multiblock).
[    9.301297] IFX DEU AES initialized (multiblock).
[    9.305450] IFX DEU ARC4 initialized (multiblock).
[    9.309819] IFX DEU SHA1 initialized.
[    9.313437] IFX DEU MD5 initialized.
[    9.317026] IFX DEU SHA1_HMAC initialized.
[    9.321107] IFX DEU MD5_HMAC initialized.
[    9.333701] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    9.398080] NET: Registered protocol family 24
[    9.425741] xt_time: kernel timezone is -0000
[    9.528752] Broadcom 43xx driver loaded [ Features: PNL ]
[    9.534686] kmodloader: done loading kernel modules from /etc/modules.d/*
[   11.140661] urandom_read: 5 callbacks suppressed
[   11.140673] random: jshn: uninitialized urandom read (4 bytes read)
[   11.224549] random: jshn: uninitialized urandom read (4 bytes read)



BusyBox v1.30.0 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r9131-5bac623895
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# 
root@OpenWrt:/# [   30.558309] br-lan: port 1(eth0) entered blocking state
[   30.562230] br-lan: port 1(eth0) entered disabled state
[   30.567793] device eth0 entered promiscuous mode
[   30.632785] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   31.921575] jffs2: notice: (1184) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   32.567309] overlayfs: upper fs does not support tmpfile.
[   32.612675] lantiq,xrx200-net 1e108000.eth eth0: port 0 got link
[   32.624873] br-lan: port 1(eth0) entered blocking state
[   32.628737] br-lan: port 1(eth0) entered forwarding state
[   32.680558] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Mit Zitat antworten
  #524  (Permalink
Alt 26.01.2019, 09:27
A1B2C3D4 A1B2C3D4 ist offline
Senior Mitglied
 
Registriert seit: 28.08.2013
Beiträge: 11.050
Provider: T VVDSL, VF DOCSIS 3.0
Standard AW: Speedport W724V

Zitat:
Zitat von DanijelT Beitrag anzeigen
Hello. I recently got W724v Typ B and I'd like port OpenWrt to it. The problem is U-Boot, while I could port generic Lantiq version to the board, it would be helpful if I had their U-Boot source for reference.

Is this source archive still available somewhere? Telekom removed all GPL downloads from their website and now provide them only upon written request to their open source team, and considering that I'm not from Germany, I don't know if I could accomplish anything.
The archive is still lying around on the Telekom server, you just have to guess the right URL.

https://www.telekom.de/hilfe/downloa...e_20140627.tgz
Mit Zitat antworten
  #525  (Permalink
Alt 15.03.2019, 20:04
eifelman eifelman ist offline
Senior Mitglied
 
Registriert seit: 26.12.2005
Ort: bei Bitburg / Trier
Alter: 34
Beiträge: 4.356
Provider: Telekom
Bandbreite: VVDSL 50
Standard AW: Speedport W724V

Neue Firmware für den W 724V Typ B erschienen.

Firmwareänderungen -> V 01011603.06.003

- Verbessert: Signalisierung eingehender Anrufe mit unterdrückter Rufnummer
- Verbesserte Unterstützung von Hausnotrufsystemen

Download

https://www.telekom.de/hilfe/downloa...603-06-003.bin
__________________
MagentaZuhause M mit MagentaTV Plus
Mit Zitat antworten
  #526  (Permalink
Alt 07.05.2019, 21:05
eifelman eifelman ist offline
Senior Mitglied
 
Registriert seit: 26.12.2005
Ort: bei Bitburg / Trier
Alter: 34
Beiträge: 4.356
Provider: Telekom
Bandbreite: VVDSL 50
Standard AW: Speedport W724V

Neue Firmware für den W 724V Typ C erschienen.

Firmwareänderungen -> V 09011603.06.003

- Neu: Unterstützung des schnellen Online-Updates (CDN), mit kürzerer Unterbrechung der Verbindung
- Verbessert: Nach netzseitigen Störungen konnte der Speedport die Verbindung nicht immer reaktivieren (LCP)
- Verbessert: Bei partiellen Ausfällen im Telefonnetz sind Gespräche weiterhin möglich
- Behoben: Es konnte zum Abbruch abgehender Telefonate kommen, wenn die regionale Zielrufnummer an ein Mobiltelefon weitergeleitet wurde
- Verbessert: Telefonverbindungsaufbau zu M-Net Kunden
- Behoben: In einem Telefonat zu einem Mobiltelefon konnte es in seltenen Fällen zu einem Abbruch des Gesprächs kommen, nachdem eine auf Mobilfunkseite gehaltene Verbindung reaktiviert wurde
- Verbesserte Datenübertragung über Telefonie-Verbindungen, z.B. Fax-Übertragung (V.152 Protokoll)
- Behoben: Bei der Nutzung von WLAN TO GO konnte es dazu kommen, dass Anwendungen im Internet (TCP Queries) nicht erreichbar waren

Download

https://www.telekom.de/hilfe/downloa...603-06-003.bin
__________________
MagentaZuhause M mit MagentaTV Plus
Mit Zitat antworten
 
Anzeige
Antwort


Aktive Benutzer in diesem Thema: 1 (Registrierte Benutzer: 0, Gäste: 1)
 
Themen-Optionen

Forumregeln
Es ist Ihnen nicht erlaubt, neue Themen zu verfassen.
Es ist Ihnen nicht erlaubt, auf Beiträge zu antworten.
Es ist Ihnen nicht erlaubt, Anhänge hochzuladen.
Es ist Ihnen nicht erlaubt, Ihre Beiträge zu bearbeiten.

BB-Code ist an.
Smileys sind an.
[IMG] Code ist an.
HTML-Code ist aus.

Gehe zu

Ähnliche Themen
Thema Autor Forum Antworten Letzter Beitrag
Vdsl mit speedport w700v und modem speedport hs300 pepe85 VDSL und Glasfaser 29 07.07.2011 17:35
Fritz!Box 7270 hinter Speedport 300HS (ohne Speedport W701V dazwischen) Engelbarts VDSL und Glasfaser 22 14.06.2008 08:09
speedport 701 und speedport 300hs -> port freigeben IhlieDaily VDSL und Glasfaser 1 17.04.2008 07:45
speedport W701 mit externem Speedport 200 als Modem rudisorglos Sonstiges 4 06.03.2008 10:41
Speedport W 500 oder Speedport W 701V Rumbah ADSL und ADSL2+ 6 14.09.2006 08:01


Alle Zeitangaben in WEZ +2. Es ist jetzt 07:40 Uhr.


Basiert auf vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.